除水劑對改性硅烷聚醚丁基防水嵌縫膠的性能...
2025-04-28
推薦新聞
固化劑添加量對硅烷改性聚氨酯密封膠剪切強...
2025-04-28
固化劑和除水劑的用量對MS密封膠力學性能...
2025-04-28
焊縫MS密封膠問題及原因分析
2025-04-27
焊縫丁基防水嵌縫膠出現破損及開裂原因
2025-04-27
A組分NC對硅烷改性聚氨酯密封膠的影響
- 發布時間 : 2025-3-19 17:33:52
- Views:
(Summary description)Customized SILICONE STRUCTURAL SEALANT from China manufacturer refers to the adhesive with high strength, can bear large load, aging resistance, fatigue resistance and corrosion resistance, and has stable performance within the expected life. It is suitable for bearing the bonding of strong structural parts. Non structural adhesive has low strength and poor durability. It can only be used for bonding, sealing and fixing of ordinary and temporary properties, and cannot be used for structural adhesive bonding. NEUTRAL SILICONE WETHERPROOF SEALANT from China manufacturer is a structural adhesive with waterproof function. Silicone glue refers to the adhesive based on silicone rubber. According to different functions, it can be divided into structural adhesive, potting adhesive, sealant, thermal conductive adhesive, flame retardant adhesive and so on.
A組分NC對硅烷改性聚氨酯密封膠的影響
(Summary description)Customized SILICONE STRUCTURAL SEALANT from China manufacturer refers to the adhesive with high strength, can bear large load, aging resistance, fatigue resistance and corrosion resistance, and has stable performance within the expected life. It is suitable for bearing the bonding of strong structural parts. Non structural adhesive has low strength and poor durability. It can only be used for bonding, sealing and fixing of ordinary and temporary properties, and cannot be used for structural adhesive bonding. NEUTRAL SILICONE WETHERPROOF SEALANT from China manufacturer is a structural adhesive with waterproof function. Silicone glue refers to the adhesive based on silicone rubber. According to different functions, it can be divided into structural adhesive, potting adhesive, sealant, thermal conductive adhesive, flame retardant adhesive and so on.
- 發布時間 : 2025-3-19 17:33:52
- Views:
Information
將不同聚氨酷預聚體(pre-PU-A 1, pre-PU-A2 ,pre-PU-A3 , pre-PU-A4, pre-PU-AS)制備的硅烷改性聚氨酯密封膠用于薄膜復合，并對復合膜性能進行測試。圖3是水煮前后各層剝離力和熱合強度的測試結果。隨。NC'。增大，硅烷改性聚氨酯密封膠硬段質量分數略微增加，軟段中PET-B質量分數由43.7%增加至50.9% o RCPP/Al(耐蒸煮聚丙流延膜/鋁箔)層的剝離力隨預聚體。NC'。增大呈現先減小后增大趨勢，這是因為硅烷改性聚氨酯密封膠剛性增加，與基材貼合程度降低。而隨著。NC'。進一步增加，PET-B中環的缺電子結構與鋁箔表面靜電吸附作用增加，剝離力增大。PET/Al}聚對苯二甲酸乙二醇酷/鋁箔)層剝離力先增大后減小，這是由于PET-B質量分數增加，硅烷改性聚氨酯密封膠對鋁箔吸附作用增強，應力作用導致硅烷改性聚氨酯密封膠從PET膜上剝離。熱合強度隨。NC'。增加而增大，可能是因為硅烷改性聚氨酯密封膠剛性增大使得復合膜強度增強。經水煮后，硅烷改性聚氨酯密封膠各層剝離力隨預聚體。NC'。增大而增大，這是因為PET-B中含有苯環和帶有支鏈的綜上，r}N}.o=17%時，聚氨酷預聚體茹度較小，所制備的聚氨酷硅烷改性聚氨酯密封膠易于涂覆且水煮后剝離力較高，因此優選聚氨酷預聚體的。Nco I 7%。PET-A分子量對硅烷改性聚氨酯密封膠鉆度的影響在40℃條件下，持續測試由不同PET-A制備的聚氨酷硅烷改性聚氨酯密封膠茹度。測試結果如圖4所示，隨PET-A分子量減小，預聚體中游離MDI減少，與輕基的反應性降低，硅烷改性聚氨酯密封膠茹度達到5 000 mPas所需時間由40 min增加至 48 min。硅烷改性聚氨酯密封膠達到5 000 mPa}s的時間反映了硅烷改性聚氨酯密封膠的固化速率，隨原料組成PET-A分子量減小，硅烷改性聚氨酯密封膠固化速率下降。http://ago-games.com/
Scan the QR code to read on your phone
+86-
13573398725
sdyuantai@163.com
搜索