導致丁基防水嵌縫膠性能發生變化的關鍵因素
2025-04-29
推薦新聞
配比對單組分聚氨酯密封膠低溫表干時間及固...
2025-04-29
催化劑的不同量搭配對硅烷改性聚氨酯密封膠...
2025-04-29
除水劑對改性硅烷聚醚丁基防水嵌縫膠的性能...
2025-04-28
固化劑添加量對硅烷改性聚氨酯密封膠剪切強...
2025-04-28
擴鏈系數對MS密封膠性能的影響
- 發布時間 : 2025-4-13 15:32:44
- Views:
(Summary description)Customized SILICONE STRUCTURAL SEALANT from China manufacturer refers to the adhesive with high strength, can bear large load, aging resistance, fatigue resistance and corrosion resistance, and has stable performance within the expected life. It is suitable for bearing the bonding of strong structural parts. Non structural adhesive has low strength and poor durability. It can only be used for bonding, sealing and fixing of ordinary and temporary properties, and cannot be used for structural adhesive bonding. NEUTRAL SILICONE WETHERPROOF SEALANT from China manufacturer is a structural adhesive with waterproof function. Silicone glue refers to the adhesive based on silicone rubber. According to different functions, it can be divided into structural adhesive, potting adhesive, sealant, thermal conductive adhesive, flame retardant adhesive and so on.
擴鏈系數對MS密封膠性能的影響
(Summary description)Customized SILICONE STRUCTURAL SEALANT from China manufacturer refers to the adhesive with high strength, can bear large load, aging resistance, fatigue resistance and corrosion resistance, and has stable performance within the expected life. It is suitable for bearing the bonding of strong structural parts. Non structural adhesive has low strength and poor durability. It can only be used for bonding, sealing and fixing of ordinary and temporary properties, and cannot be used for structural adhesive bonding. NEUTRAL SILICONE WETHERPROOF SEALANT from China manufacturer is a structural adhesive with waterproof function. Silicone glue refers to the adhesive based on silicone rubber. According to different functions, it can be divided into structural adhesive, potting adhesive, sealant, thermal conductive adhesive, flame retardant adhesive and so on.
- 發布時間 : 2025-4-13 15:32:44
- Views:
Information
當預聚物NCO質量分數為9. 4%，后固化時間為7d時，擴鏈系數對MS密封膠拉伸剪切強度和硬度的影響如表2所示。表2擴鏈系數對MS密封膠性能的影響擴鏈系數拉伸剪切強度/MPa召仔A硬度可知，當預聚物NCO含量和后固化時間不變時，隨擴鏈系數增加，MS密封膠的拉伸剪切強度和硬度先增大后減小，并且在擴鏈系數為0. 95時最大。因為擴鏈系數<<1. 0時，MS密封膠在固化時發生了兩個擴鏈反應，一個是異氰酸醋和IPDA的擴鏈反應，一個是后固化時殘留的異氰酸醋基和水的擴鏈反應。隨著擴鏈系數的增加，兩個反應中IPDA的擴鏈反應占比增加，而水的擴鏈反應占比下降，MS密封膠的拉伸剪切強度和硬度增大，說明IPDA擴鏈的MS密封膠拉伸剪切強度和硬度高于水擴鏈的MS密封膠;當擴鏈系數為1. 0時，解封的異氰酸醋基團與水分存在副反應，少量的IPDA沒與異氰酸醋發生擴鏈反應，起增塑作用，造成MS密封膠拉伸剪切強度和硬度降低。擴鏈系數為0. 95時，NCO稍過量，保證了固化，MS密封膠的拉伸剪切強度和硬度最大，達到5. 97MPa，邵A硬度為99。http://ago-games.com/
Scan the QR code to read on your phone
上一篇: 封閉型丁基防水嵌縫膠的DSC分析
下一篇: 單組分聚氨酯密封膠的過程中確定反應溫度
上一篇: 封閉型丁基防水嵌縫膠的DSC分析
下一篇: 單組分聚氨酯密封膠的過程中確定反應溫度
+86-
13573398725
sdyuantai@163.com
搜索